Crestron SWAMP(I)-24X8 Spezifikationen Seite 31
- Seite / 60
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System
Configuration
After making all hardware connections, the SWAMP-24X8 must be configured for
operation. The SWAMP-24X8 can be configured from the SWAMP-24X8’s front
panel using the “Installer Mode” menu or from a PC using the Sonnex Tools
application in Crestron Toolbox. This document contains instructions for using the
"Installer Mode” menu. For information on using Sonnex Tools to configure the
SWAMP-24X8, refer to the Sonnex Tools help file.
Enter the “Installer Mode”
Menu
To enter the “Installer Mode” menu, press and hold the T and ▲ buttons for
approximately five seconds. The “Installer Mode” menu is displayed.
“Installer Mode” Menu
The “Installer Mode” menu is separated into seven menus:
•
Source Setup: Select this option to adjust the compensation level for each
of the input sources.
•
Zone Setup: Select this option to configure each output zone’s settings for
audio, Sonnex links (busses), bridging (with other outputs) and power
output.
•
Expander Status: Select this option to view the status of each connected
SWAMPE Sonnex Multiroom Audio Expander.
•
Amplifier Status: Select this option to view the settings and operating
status of each of the SWAMP-24X8 amplifiers as well as the amplifiers of
connected SWAMPE Sonnex Multiroom Audio Expanders.
• Network Setup: Select this option to configure and view the Ethernet
settings of the SWAMP-24X8.
• Control Setup: Select this option to configure the SWAMP-24X8 for use
with a Crestron control system and lock/unlock the front panel controls.
•
About: Select this option to view information about the firmware.
NOTE: Changes made to any setting are only saved upon exiting the “Installer
Mode” menu. For instructions on exiting the “Installer Mode” menu, refer below.
Exit the “Installer Mode” Menu
To exit the “Installer Mode” menu, press the MENU button until the “Installer
Mode” menu is displayed (refer to illustration above), release and press MENU
again.
Source Setup
Select this option to adjust the compensation level of each input source. To set the
compensation level:
1.
Enter the “Installer Mode” menu as described above.
2.
Press ENTER to select Source Setup.
Operations Guide – DOC. 7049B Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 • 25
- Crestron SWAMP(I)-24X8 1
- Operations Guide 1
- Important Safety Instructions 2
- WARNING: 2
- IMPORTANT: 2
- Regulatory Compliance 3
- Contents 5
- Sonnex™ Multiroom Audio 7
- System: SWAMP(I)-24X8 7
- Introduction 7
- Features and Functions 8
- Bonus Zones 9
- Plug and Play Expansion 9
- Advanced DSP 9
- Speaker Profiles 10
- Output Bussing 10
- Passive Subwoofer Support 11
- Ultimate Integration 11
- Applications 12
- Specifications 13
- SPECIFICATION DETAILS 14
- Physical Description 16
- (191 mm) 18
- (178 mm) 18
- Pin 3 Pin 4 19
- Pin 2 Pin 1 19
- Network Wiring 22
- Sonnex Link Wiring 22
- Identity Code 22
- Installation 23
- Hardware Hookup 25
- + - G + 26
- Bridging Outputs 27
- ” which starts on page 31 29
- Configuration 31
- Gain Control 32
- EQ Setting 33
- Bass Setting 34
- Treble Setting 34
- Loudness Setting 34
- Balance Setting 35
- Mono/Stereo Setting 35
- Minimum Volume Setting 36
- Maximum Volume Setting 36
- Startup Volume Setting 36
- Bus Setting 37
- Offset Setting 37
- Bus Display 38
- Bridging Setting 38
- Wattage Setting 39
- Impedance Setting 39
- Speaker Protect Setting 40
- Crestron DRC Setting 40
- Confirm Global EQ Setting 40
- IP Address 42
- Subnet Mask 42
- Default Router 43
- DHCP Setting 43
- WINS Setting 43
- Front Panel Lock Settings 44
- Cresnet ID Setting 45
- IP ID Setting 45
- Control System IP Address 45
- Programming Software 47
- Uploading and Upgrading 50
- PC Running 51
- Crestron Toolbox 51
- SWAMP-24X8 51
- Program Checks 52
- Operation 53
- Problem Solving 54
- Cable Length Equation 55
- Future Updates 56
- Return and Warranty Policies 57
- Tel: 888.CRESTRON 01.12 60
Verwandte Produkte und Handbücher für Empfänger Crestron SWAMP(I)-24X8
Empfänger Crestron QM-RMCRX-BA Spezifikationen
(76 Seiten)
(76 Seiten)
Empfänger Crestron SP-1 Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Empfänger Crestron SP-1 Spezifikationen
(24 Seiten)
(24 Seiten)
Empfänger Crestron ABVR-1 Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger Crestron CNXRMIRD Spezifikationen
(36 Seiten)
(36 Seiten)
Empfänger Crestron SP-1 Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Empfänger Crestron CNXRMIRD Bedienungsanleitung
(12 Seiten)
(12 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.358 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern