Crestron CLSI-C6M Spezifikationen PDF herunterladen (Seite 2)

iLux

™

Lighting Systems

Physical Description

NOTE: The CLSI-C6 units require a neutral wire for

operation. If no neutral is present, contact a licensed

electrician for installation.

The following illustration shows the overall dimensions

for the CLSI-C6 and CLSI-C6M.

The following tools/hardware are required for installation.

CLSI-C6M Overall Dimensions

• A 4-gang electrical box (not supplied), 3.5 inches

deep, minimum.

8.89 in

(22.58 cm)

4.48 in

(11.38 cm)

1.88 in

(4.77 cm)

2.38 in

(6.05 cm)

0.59 in

(1.49 cm)

CLSI-C6

0.72 in

(1.83 cm)

CLSI-C6M

• Phillips torque screwdriver (not supplied)

• Four 7/8-inch pan head Phillips screws

(supplied)

If the planned configuration includes connection to shade

controllers, keypads, and/or a Crestron 2-Series control

system, the following items are also required. Refer to the

latest version of the Crestron CLSI-C6 & CLSI-C6M

iLux Lighting System Operations Guide, Doc. 6347, for

detailed configuration options.

• Cresnet network cable(s) (not supplied)

Industry Compliance

• Terminal block connector(s) (two supplied)

These units have been designed to comply with IEC

60669-2-1 and specifications for CE marking. Formal

approval is pending.

Check that any required Cresnet wiring has been installed

and verified. Then, use the following procedure to install

the iLux unit (CLSI-C6M is shown in the illustrations).

Important Notes

1. Feed the wires (power line from the distribution

panel, load wires, plus any required Cresnet

cables) through the holes in the wallbox. Then

install the box in the wall.

Read before installation.

• Codes: Install in accordance with all local and

national electrical codes.

2. Hold the rear of the CLSI-C6M unit and remove

the front panel and cover assembly by carefully

Remove the control panel overlay from the u

• Wiring: Use copper wire only. For supply

connections, use wires rated for at least 75°C.

pulling out and up from the bottom edge.

3. nit

4. of

• Lighting Load Types: incandescent, magnetic

low voltage, neon/cold cathode, and non-dim

lighting.

• Temperature: The iLux units are designed for

use where temperatures are between 32° to

104°F (0° to 40°C).

• Wallboxes: The iLux units mount in standard

4-gang wallboxes; 3.5 inches deep, minimum.

• Make certain that power is turned off, and

ensure that there is at least 12 inches of open

space above and below the electrical box

location to permit heat dissipation.

Installation

(it lifts off – is held in place by small tabs) to

reveal the upper mounting screw holes.

Refer to the following diagram for connection

WARNING: Turn off power at the distribution panel

circuit breaker. Installing with power on can result in

serious personal injury and damage to the device.

the AC wiring. All wires to be inserted in the

screw terminals should be stripped 7/16-inch,

and screws should be tightened to between 8 an

10 in.-lbs. (0.90 Newton meters to 1.13 Newton

meters). The maximum wire size is 12 AWG

(3 mm²).

CAUTION: To reduce the risk of overheating and

possible damage to other equipment, do not install to

control a receptacle or a motor-operated appliance.

2 • iLux

™

Lighting Systems: CLSI-C6 & CLSI-C6M Installation Guide – DOC. 6413B

1 2 3 4

Lighting Systems 1

Kommentare zu diesen Handbüchern

Keine Kommentare

Crestron CLSI-C6M Spezifikationen Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Crestron CLSI-C6M