
CP3N 3-Series Control System
®
crestron.com
|
800.237.2041
IR/Serial: Supports 1-way device control via infrared up to 1.2 MHz or
serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
Connectors & Card Slots
RELAY OUTPUT 1 – 8: (2) 8-pin 3.5mm detachable terminal blocks
comprising (8) normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC; MOV arc suppression across contacts
I/O 1 – 8: (1) 9-pin 3.5mm detachable terminal block comprising
(8) “Versiport” digital input/output or analog input ports (referenced
to GND);
Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms, logic
threshold >3.125V low/0 and <1.875V high/1;
Digital Output: 250mA sink from maximum 24 Volts DC, catch diodes for
use with “real world” loads;
Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum,
input impedance 21k Ohms with pull-up resistor disabled;
Programmable 5 Volts, 2k Ohms pull-up resistor per pin
IR - SERIAL OUTPUT 1 – 8: (2) 8-pin 3.5mm detachable terminal block
comprising (8) IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
COM 1: (1) 5-pin 3.5mm detachable terminal block;
Bidirectional RS-232/422/485 port;
Up to 115.2k baud; hardware and software handshaking support
COM 2 – 3: (2) 3-pin 3.5mm detachable terminal blocks;
Bidirectional RS-232 ports;
Up to 115.2k baud; software handshaking support
MEMORY: (1) SD memory card slot;
Accepts one SD or SDHC card up to 32 GB for memory expansion
USB: (1) USB Type A female; USB 2.0 port for storage devices
LAN: (1) 8-wire RJ45 jack;
10Base-T/100Base-TX/1000Base-T Ethernet port;
Connects to the customer’s LAN
CONTROL SUBNET: (1) 8-wire RJ45 jack;
10Base-T/100Base-TX/1000Base-T Ethernet port;
Provides a dedicated local network for Crestron devices
NET: (1) 4-pin 3.5mm detachable terminal block, Cresnet master port;
Outputs power to Cresnet devices if a power pack is connected to the
24VDC power input jack;
Receives Cresnet network power if no power pack is connected to the
24VDC power input jack;
See “Power Requirements” for additional specifications
24VDC 2.0A: (1) 2.1 x 5.5 mm DC power connector;
24 Volt DC power input; PW-2420RU power pack included;
Passes through to NET port to power Cresnet devices;
See “Power Requirements” for additional specifications
G: (1) 6-32 screw, chassis ground lug
COMPUTER (front): (1) USB Type B female;
USB 2.0 computer console port (6 ft cable included);
For setup only
Controls & Indicators
PWR: (1) Green LED, indicates operating power supplied from power pack
or Cresnet network
NET: (1) Amber LED, indicates communication with the Cresnet system
MSG: (1) Red LED, indicates control system has generated an
error message
HW-R: (1) Recessed pushbutton for hardware reset
SW-R: (1) Recessed pushbutton for software reset
LAN (rear): (2) Bi-color green/amber LEDs, left LED indicates Ethernet link
status and connection speed, right LED indicates Ethernet activity
CONTROL SUBNET (rear): (2) Bi-color green/amber LEDs, left LED
indicates Ethernet link status and connection speed, right LED indicates
Ethernet activity
Power Requirements
Power Pack: 2.0 Amps @ 24 Volts DC;
100-240 Volts AC, 50/60 Hz power pack, model PW-2420RU included
Available Cresnet Power: 24 Watts (1 Amp @ 24 Volts DC) when using
power pack
Cresnet Power Usage: 15 Watts (0.625 Amp @ 24 Volts DC) when using
Cresnet network power
Environmental
Temperature: 41° to 113°F (5° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 50 BTU/Hr
Enclosure
Chassis: Metal, black finish
Faceplate: Extruded metal, black finish, polycarbonate label overlay
Mounting: Freestanding or 1U 19-inch rack-mountable (adhesive feet and
rack ears included)
Dimensions
Height: 1.70 in (44 mm) without feet
Width: 17.28 in (439 mm);
19.00 in (483 mm) with rack ears
Depth: 6.56 in (167 mm)
Weight
3.1 lb (1.42 kg)
Kommentare zu diesen Handbüchern