Crestron APAD Bedienungsanleitung PDF herunterladen (Seite 3)

Pb, Y, Pr OUTPUT 1: (3) BNC female, component/HDTV ( YPBPR) video output

Output Level: 1.0 to 1.1 V

P-P (terminated, with 1 VP-P input)

Output Impedance: 75 ohms nominal

RGBHV OUTPUT 1: (1) DB15HD female

RGBHV, component, S-Video, and composite video output

Formats: RGBHV, RGBS, YPbPr, Y/C, composite

RGB/Video Output Level: 0.7 to 0.75 Vp-p (terminated, with 0.7 Vp-p input, unity gain)

RGB/Video Output Impedance: 75 ohms nominal

H/V Sync Output Level: 4 to 5 Vp-p

H/V Sync Output Impedance: 55 ohms

H/V Sync Polarity: Follows input

TOUCHPANEL CH 2: (1) 8-wire RJ45 female, CAT5 balanced video output port

Signal Types: Dynamically configurable for component ( YP

BPR), S-Video (Y/C), or

composite video;

Video/HDTV Formats: NTSC or PAL, HDTV up to 1080i

Output Impedance: 100 ohms balanced

Connects to CH CAT5 balanced video input port of a compatible touchpanel or other

device via CresCAT cable

TOUCHPANEL QM 2: (1) 8-wire RJ45 female, QuickMedia output port

Signal Types: Dynamically configurable for RGBHV, component ( YP

BPR), S-Video (Y/C),

or composite video with stereo program audio;

RGB Format: RGBHV, RGBS

RGB Output Resolution, Non-interlaced: 1920 x 1200 maximum (60Hz limit at 1600 x

1200 or higher);

Video/HDTV Formats: NTSC or PAL, HDTV up to 1080i/1080p

Connects to QM input port of a compatible touchpanel or other QuickMedia device via

CresCAT-QM or CresCAT-IM cable

[1]

Connectors – Control & Power

IR/SERIAL OUT A - D: (4) 2-pin 3.5mm detachable terminal blocks, IR/Serial output ports

IR output up to 1.2 MHz

1-way serial TTL/RS-232 (0-5 Volts) up to 9600 baud

IR IN: (1) 3-pin 3.5mm detachable terminal block

For connection of the CNXRMIRD IR Receiver (sold separately)

Allows control from IR wireless remotes using RC-5 command set

INPUT 1 - 4: (1) 5-pin 3.5mm detachable terminal block

Comprises (4) digital/contact closure inputs

Rated for 0-24 Volts DC, referenced to GND

Input Impedance: 2.2k ohms pulled up to 5 Volts DC

Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band

RELAY 1 - 4: (1) 8-pin 3.5mm detachable terminal block

Comprises (4) normally open, isolated relays

Rated 1 Amp, 30 Volts AC/DC

MOV arc suppression across contacts

COM A - B: (2) DB9 male, bidirectional RS-232 ports

Up to 115.2k baud, hardware and software handshaking support

LAN: (1) 8-wire RJ45 with 2 LED indicators, 10/100BaseT Ethernet port

Green LED indicates link status, Yellow LED indicates Ethernet activity

NET: (4) 4-pin 3.5mm detachable terminal blocks, Cresnet Master ports, paralleled

Available Cresnet Power: 30 Watts

G: (1) 6-32 screw, chassis ground lug

100-240V~2.5A: (1) IEC Socket, main power input

Mates with removable power cord, included

COMPUTER (front): (1) USB Type B female

USB 1.1 computer console port (cable included)

LCD Display

Green LCD alphanumeric, adjustable backlight, 2 lines x 20 characters per line

Displays input/outputs by name, volume level bargraph, setup menus, time/date, and

other system information

Controls and Indicators

NET: (1) yellow LED, indicates Cresnet bus activity

MSG: (1) yellow LED, indicates control system has generated an error message

HW-R: (1) recessed miniature pushbutton for hardware reset, reboots the control system

SW-R: (1) recessed miniature pushbutton for software reset, restarts the SIMPL program

SYS PWR: (1) pushbutton and green LED, controls system power

PROJ PWR: (1) pushbutton and green LED, controls display device power

SOFTKEYS: (4) pushbuttons for activation of LCD driven functions and passcode entry

MENU: (1) pushbutton, steps menu back one level

,V:

(2) pushbuttons, scroll up or down through menu and adjust menu parameters

ENTER: (1) pushbutton, executes highlighted menu or value

VOLUME: (1) continuous turn rotary encoder, adjusts menu parameters, defaults to

program audio volume

FUNCTION 1 – 5: (5) pushbuttons and red LEDs, programmable for any control system

function

IN 1 – 5: (5) pushbuttons and red LEDs, select input to be routed

OUT 1 – 2: (2) pushbuttons and red LEDs, select output destination

Power Requirements

Main Power: 2.5 Amps @ 100-240 Volts AC, 50/60 Hz

Available Cresnet Power: 30 Watts

Environmental

Temperature: 41° to 104°F (5° to 40°C)

Humidity: 10% to 90% RH (non-condensing)

Enclosure

Chassis: Steel, black matte powder coat finish, convection-cooled, vented top and sides

Faceplate: Extruded aluminum, black matte powder coat finish with polycarbonate label

overlay

Mounting: Freestanding or 2U 19-inch rack-mountable (adhesive feet and rack ears

included)

Dimensions

Height: 3.56 in (90 mm), 3.47 in (88 mm) without feet

Width: 17.03 in (433 mm), 19.0 in (483 mm) with ears

Depth: 12.54 in (319 mm)

Weight

MPS-100: 8.8 lb (4.0 kg)

MPS-100-70V/100V: 10.6 lb (4.8 kg)

For QuickMedia wiring use CresCAT-QM, CresCAT-IM, or quality CAT5e/CAT6 cable

with a delay skew of 15nS per 100m; the maximum aggregate cable length and delay

skew between any QM transmitter (origination point) and QM receiver (endpoint) is

450 ft (137 m) and 22 nS; a maximum of two QM midpoint devices may be inserted

in a given QM signal path; exceptions apply, refer to each respective product manual

for full detail.

Crestron MPS-100 Multimedia Presentation System 100

LANLAN

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Crestron APAD Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Datenprojektoren Crestron APAD