Crestron infiNET Gateway C2N-MNETGW Spezifikationen PDF herunterladen

infiNET™ DIMMERS

Introduction

Features and Functions

The CLW-DIM1RF (-DIM1RF) and CLW-DIM4RF

(-DIM4RF) are stand-alone wall box dimmers that can

also act as wireless infiNET™ devices that report to a

Crestron

control processor through an infiNET gateway

such as the Crestron C2N-MNETGW. The -DIM1RF and

-DIM4RF have three preset lighting levels that can be

adjusted. For more information, refer to the latest version

of the infiNET Dimmers Operations Guide (Doc. 6396)

which is available from the Crestron website

(www.crestron.com/manuals).

These dimmers are part of Crestron’s line of lighting

products using infiNET mesh network technology.

infiNET technology is “Wi-Fi” friendly and provides fault

tolerance and increased effective signal strength as

network devices are added.

Crestron Electronics, Inc. Installation Guide – DOC. 6292C

15 Volvo Drive Rockleigh, NJ 07647 (2011321)

Tel: 888.CRESTRON 03.09

Up to 30 infiNET devices (including C2N-MNETRPT

infiNET Repeaters) can communicate with one

C2N-MNETGW Gateway. If more devices are needed,

more C2N-MNETGW gateways may be added to a

Cresnet

network.

The infiNET dimmers operate on the 2.4 GHz “ISM

band” (2400 MHz to 2483.6 MHz) at 10 mW. The output

power of these devices allow RF signals to travel

approximately 150 feet indoors and 250 feet outdoors

(subject to site-specific conditions) without the use of

repeaters or other infiNET devices. The range is

dependent on construction of the building, obstructions,

and RF interference from other devices. The location of

the dimmer is an important factor in determining RF

performance. Adding more infiNET devices or repeaters

to the network effectively increases the range, strength,

and reliability of the network.

The -DIM1RF and -DIM4RF feature a three-position

mode selection switch. For more information, refer to the

latest version of the infiNET Dimmers Operations Guide

(Doc. 6396) which is available from the Crestron website.

In the absence of control system communications, the

dimmer can still be used to control the attached load.

The CLW-DIMS1RF (-DIMS1RF) and CLW-DIMS4RF

(-DIMS4RF) are similar to the -DIM1RF and -DIM4RF

(respectively) with the added capability of working with

one or more slave units (CLW-SLVD1RF) in a multi-

dimmer / single circuit application.

The CLW-SLVD1RF (-SLVD1RF) is a slave unit that

when used in conjunction with the -DIMS1RF or

-DIMS4RF acts as an additional dimmer control point in a

multi-dimmer / single circuit application. It does not

connect to a Cresnet system and cannot be used without a

-DIMS1RF or -DIMS4RF. The -SLVD1RF does not have

a mode selection switch. It will emulate the RUN mode of

the -DIMS1RF (even if connected to a -DIMS4RF) unless

the mode selection switch of the master is set to “OFF”.

For more information, refer to the latest version of the

infiNET Dimmers Operations Guide (Doc. 6396) which is

available from the Crestron website.

These dimmers are available in a variety of colors and

textures. The table below shows the availability.

Available Colors/Textures

COLOR/

TEXTURE

MODEL NUMBER

SUFFIX

MATCHING LUTRON

FACEPLATE

White W Not Applicable

Smooth White W-S CW-1-WH

Almond A CW-1-LA

Smooth Almond A-S CW-1-LA

Black B Not Applicable

Smooth Black B-S CW-1-BL

Specifications

Following are specifications for the -DIM1RF, -DIM4RF,

-DIMS1RF, -DIMS4RF, and -SLVD1RF.

CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, &

CLW-SLVD1RF Specifications

SPECIFICATION DETAILS

Power Requirements Line Power, 120 VAC, 60 Hz

Operating Frequency 2400 MHz to 2483.6 MHz

(802.15.4 compliant)

RF Output Power 10 mW

Operating Ranges¹

Typical Distance

Indoors

(without repeater)

Typical Distance

Outdoors

150 ft

250 ft

(subject to site-specific

conditions)

Default MNET ID -DIM1RF/-DIM4RF: 01/01

-DIMS1RF/-DIMS4RF: 01/01

Switch Type Dimmer

Load Type Incandescent, Tungsten-

Halogen, Magnetic Low Voltage

2-Series Control System

Update File

2,3

Version 3.154 or later

Load Ratings

Incandescent/Tungsten-

Halogen

-DIM1RF/-DIM4RF: 1000W

-DIMS1RF/-DIMS4RF: 1000W

-SLVD1RF: N/A

(continued on following page)

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - Introduction

infiNET™ DIMMERS Introduction Features and Functions The CLW-DIM1RF (-DIM1RF) and CLW-DIM4RF (-DIM4RF) are stand-alone wall box dimmers that can al

Seite 2 - Physical Description

infiNET™ DIMMERS To continue a circuit past a switched light fixture to one or more duplex receptacles, connect the dimmer as shown in the following

Seite 3

infiNET™ DIMMERS In this configuration: • The white wire from the DIMSXRF to the load is coded HOT. • The white wire of the -SLVD1RF must be cappe

Seite 4 - DO NOT REMOVE OUTER SECTIONS

infiNET™ DIMMERS This page is intentionally left blank. 12 • infiNET™ Wall Box Dimmer : CLW-DIM1/4RF, DIMS1/4RF, & SLVD1RF Installation Gui

Seite 5 - Installation

infiNET™ DIMMERS CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, & CLW-SLVD1RF Specifications (continued) SPECIFICATION DETAILS Load Ratings (continu

Seite 6 - Testing a -SLVD1RF

infiNET™ DIMMERS Physical view of CLW-DIM4RF/-DIMS4RF (clockwise from top; Top, Side, and Front) RUN SET OFF1.75 in(4.45 cm)2.38 in(6.03 cm)3.28 in

Seite 7 - Problem Solving

infiNET™ DIMMERS • Wallboxes: Devices mount in standard wallboxes. For easy installation, Crestron recommends using 3 ½” deep wallboxes. Several de

Seite 8 - CRESTRON Limited Warranty

infiNET™ DIMMERS Installation WARNING: Turn off power at the circuit breaker. Installing with power on can result in serious personal injury and da

Seite 9 - Appendix: Wiring Diagrams

infiNET™ DIMMERS Testing NOTE: The device may be warm to the touch during operation. This is normal. Test the installation by setting the dimmer’s

Seite 10 - Master-Slave Installations

infiNET™ DIMMERS NOTE: Holding the button for a significant time after the first flash may enter other modes. If this is not desired, return the mo

Seite 11 - infiNET™ DIMMERS

infiNET™ DIMMERS Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or servic

Seite 12

infiNET™ DIMMERS Appendix: Wiring Diagrams Following are wiring diagrams for circuits that may be found when installing infiNET dimmers: Stand-Alone

Weitere Dokumente für Vernetzung Crestron infiNET Gateway C2N-MNETGW

Um das Dokument anzuzeigen Crestron infiNET Gateway C2N-MNETGW Bedienungsanleitung

Crestron infiNET Gateway C2N-MNETGW Bedienungsanleitung (4 Seiten)

Um das Dokument anzuzeigen Crestron infiNET Gateway C2N-MNETGW Spezifikationen

Crestron infiNET Gateway C2N-MNETGW Spezifikationen (40 Seiten)

Crestron infiNET Gateway C2N-MNETGW Spezifikationen (24 Seiten)

Crestron infiNET Gateway C2N-MNETGW Bedienungsanleitung (1 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Crestron infiNET Gateway C2N-MNETGW Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Vernetzung Crestron infiNET Gateway C2N-MNETGW herunter. Crestron infiNET Gateway C2N-MNETGW Specifications [en] Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Vernetzung Crestron infiNET Gateway C2N-MNETGW

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Crestron infiNET Gateway C2N-MNETGW