Crestron DM-MD8X8 Installationsanleitung PDF herunterladen

quickstart guide

DM-MD8X8/16X16/32X32

www.crestron.com

888.273.7876 201.767.3400

change without notice.

For details, refer to the latest version of the DM-MD8X8/16X16/32X32

DigitalMedia

™

Switchers Operations Guide, Doc. 6755.

QUICKSTART DOC. 6756D (2022813, 1 of 2) 04.10

DigitalMedia

™

Switchers

All brand names, product names, and trademarks

are the property of their respective owners.

DM-MD8X8/16X16/32X32

Before Starting

Install/Replace Input/Output Cards

CAUTION: Do not connect power cords until instructed to do so.

NOTE: Before beginning any of these QuickStart procedures, make

certain that all DigitalMedia

™

cables are installed throughout the home.

CAUTION: Input and output cards are electrostatic-sensitive devices.

Wear a grounding strap or touch the metal chassis of a known

grounded device before handling and installing cards.

NOTE: Make sure that the power cord is not connected before

installing any input or output cards.

A. Remove screws securing the card to be replaced or the plate covering

the card slot to be used. Insert the card into the slot side rails, and make

certain the card is fully seated before using the attached screws to secure it

in position. (Leave cover plates in place on unused card slots.)

Connect Outputs

The illustration immediately to the right shows the special connectors used for

the three cables contained within Crestron’s DigitalMedia

™

cable, plus CBL-HD

HDMI cable, and CresFiber with an SC50UM connector. Refer to the illustra-

tions at the far right for typical wiring configurations.

A. Use DigitalMedia cable (DM-CBL-P or DM-CBL-NP), to connect switcher

outputs directly to a DM-RMC-100 Room Controller. If required, first connect to

a DM-DR Repeater and then connect the output of the Repeater to the Room

Controller.

For detailed instructions on operation and setup of the DM-DR Repeater and

the DM-RMC-100 Room Controller, refer to the latest version of their respective

Operations & Installation Guides (Doc. 6745 and Doc. 6743).

B. Use HDMI cable, CBL-HD, to connect HDMI outputs to a local HDMI

display/receiver.

C. Use two CresFiber cables to connect the ‘D’ and ‘M’ fiber outputs to the

corresponding connectors on a local DM-RMC-100-F. DMNet control data is

carried along with video data on the ‘D’ cable.

Typical Input Card

Installation

DM-CBL-P

DM-CBL-NP

DM-DR

Repeater

DM-RMC-100

Room Controller

DM-CBL-P

DM-CBL-NP

‘D’ Video

Data

‘M’ Data

Management

‘DMNet’

Control & Power

‘D’ Video Data

‘DMNet’ Control & Power

‘M’ Data Management

Input and output cards are typically installed prior to shipment of the

DigitalMedia switchers. If, however, input cards (or output cards for the

DM-MD8X8/32X32 only) need to be installed or replaced in the ﬁeld,

follow the instructions below. For more information, refer to the latest

version of the DigitalMedia Card Installation Guide (Doc. 6757), available

from the Crestron website (www.crestron.com/manuals).

NOTE: Unless stated otherwise, all illustrations and procedures apply

equally to all switchers.

Output Slot 1

Input Slots 9 - 16

Output Slot 2

Input Slots 1 - 8

DM-MD16X16

NOTE: Output cards for the DM-MD16X16 are

not field configurable. If you need a different

configuration, contact Crestron customer service.

Output Slot 1

Output Slot 2

Input Slots 1 - 4

DM-MD8X8

Input Slots 5 - 8

Input Slots 1 - 16

Input Slots 17 - 32

Output Slots 1 - 4

DM-MD32X32

Output Slots 5 - 8

CresFiber - CONN-SC50UM

CBL-HD - HDMI Output

B. Cards may be installed in any of the slots provided,

but it is suggested that the cards be installed into the

slots in numerical order.

DMCO-22

DMCO-11

CBL-HD

‘D’ Video and

Control Data

‘M’ Data

Management

CresFiber

HDMI Output

Local HDMI

Display/Receiver

DM-RMC-100-F

1 2 3 4

DM-MD8X8/16X16/32X32 1

Inhaltsverzeichnis

Seite 1 - DM-MD8X8/16X16/32X32

Seite 2

For details, refer to the latest version of the DM-MD8X8/16X16/32X32 DigitalMedia™ Switchers Operations Guide, Doc. 6755. QUICKSTART DOC. 6756D (20228

Seite 3

For details, refer to the latest version of the DM-MD8X8/16X16/32X32 DigitalMedia™ Switchers Operations Guide, Doc. 6755. QUICKSTART DOC. 6756D (20228

Seite 4

For details, refer to the latest version of the DM-MD8X8/16X16/32X32 DigitalMedia™ Switchers Operations Guide, Doc. 6755. QUICKSTART DOC. 6756D (20228